Don't undervalue the forklift at the workplace. If the procedure is bad, there will be major accidents in minutes, and there are several crashes including forklifts.

Situation 1: The forklift cargo obstructed the vehicle driver's sight, and the individual in front can not be discovered, resulting in a moving accident.
Situation 2: In order to maintain the equilibrium of the forklift when lifting hefty goods, the employees used their body weight as the weight, which nearly created casualties.
Case 3: The width of the forklift freight exceeds the permitted width of the path and holds on the roadside shelf, which virtually causes an mishap.
Instance 4: Forklift is speeding and rolls over throughout a turn.
Instance 5: The forklift motorist did not notice the pedestrian, and the pedestrian did not observe the forklift.
Case 6: The forklift raises the employees illegally, the forklift chauffeur does not put on the safety belt, the forklift lifter falls and the chauffeur is crushed when the forklift surrender.
Situation 7: The forklift vehicle driver did not put on a safety belt and dropped from the lorry when it surrendered and was squashed.
Forklift procedure should focus on these issues ：.

Begin.
1. Prior to starting, observe the surroundings, and after verifying that there are no challenges that impede the safety and security of driving, beep the horn initially and afterwards start.
2. For lorries with hydraulic ( atmospheric pressure) brakes, the brake hydraulic stress ( atmospheric pressure) scale have to be risk-free before starting.
3. When the forklift starts with a load, the driver ought to first validate that the lots is secure and reliable.
4. The beginning has to be sluggish and consistent.

Driving.
1. When driving, the height in between the bottom end of the fork and the ground need to be maintained 300mm-400mm, and the mast needs to be tilted backward. .
2. Do not raise the fork too expensive when driving. When getting in and leaving the work site or while driving, take care that there will be no obstacles overhead. When the load is taking a trip, the fork must not be elevated expensive, which will affect the security of the forklift. .
3. After unloading, the fork needs to be reduced to the regular driving position prior to driving. .
4. When turning, if there are pedestrians or lorries nearby, the driving signal must be released first. High-speed sharp turns are banned. High-speed sharp turns will certainly trigger the lorry to lose side security and tip over. .
5. When the forklift is downhill, it is strictly prohibited to switch off the fire and slide, and it is prohibited to brake instantly while driving with loads unless there are special conditions.
6. When the forklift is running, it should follow the website traffic rules in the factory and should keep a specific security range from the vehicle in front. .
7. When the forklift is running, the load should be in the most affordable position that does not hinder the driving, and the gantry should be appropriately tilted back. The load will not be elevated other than when piling or filling. .
8. The height of the tons must not obstruct the vehicle driver's view. In unique scenarios, when the product affects the forward vision, drive at a low rate when turning around.
9. It is restricted to activate the ramp, neither to drive across the ramp. .
10. The risk-free driving speed of the forklift in the factory area is 5 km/h, and it should drive safely at a reduced rate when going into the production workshop location. .
11. When the forklift is raised, raised or driven, it is forbidden for personnel to depend on the fork to hold products and play a balancing duty. .
12. If issues are found, they will certainly be fixed and reported in a timely manner, and they will certainly never operate with ailments or hide them.

loading and dumping.
1. When fork-loading things, the distance in between the two forks must be adjusted as required to make the lots of the two forks well balanced and not skewed, and one side of the product should be against the shelf. .
2. It is forbidden to collaborate with a single fork or use a fork top or draw. In special circumstances, safety and security warning signs have to be set up to remind surrounding pedestrians. .
3. In the process of filling and dumping items, the forklift should be braked with the brake. .
4. The speed of the lorry should be slow-moving and stable. Take care not to roll the wheels on the dunnage, so as not to stretch the rolled items and injure people. .
5. When making use of a fork to fork the goods, the fork should be as deep as possible under the tons, and it must be kept in mind that the fork pointer need to not touch various other items or things. The load must be stabilized with very little back tilt of the gantry to make sure that the tons does not glide in reverse. The pole can be slanted onward a little when the lots is reduced to allow for simple placement of the lots and removal of the forks. .
6. It is forbidden to fork goods at high speed and ram tough items with the fork head. .
7. When the forklift is working, it is forbidden for people to stand around the fork, so as to prevent the collapse of the goods and harm individuals. .
8. Overloading is prohibited, and it is banned to make use of forks to lift workers to participate in high-altitude operations to prevent high-altitude dropping crashes. .
9. It is not permitted to make use of the brake inertia to slip, put, round or roll things. .
10. It is not allowed to make use of forks to choose, transform pallet discharge.

Leaving .
1. It is restricted to leave the forklift when the items on the fork impend. Before leaving the forklift, you need to unload the goods or reduced the fork framework.
2. Draw the parking brake take care of to dead or depress the emergency brake button.
3. The engine is shut off and the power is cut off. (Except for special scenarios, such as the motorist does not leave the lorry's line of sight and does not go beyond 1 minute).
4. Remove the secret. .

Forklift Operation Precautions.
1. Before and after the forklift operation, the appearance must be checked, and gas, lubing oil and air conditioning water need to be added.
2. Inspect the security efficiency of starting, running and stopping.
3. Examine whether the lights and horn signals are full and reliable.
4. During the procedure of the forklift, examine whether the pressure and temperature level are normal.
5. After the forklift is running, the outside leak ought to likewise be examined and the seals need to be replaced in time.

Forklift Safety Operation Specifications.
1. You need to check before leaving the car;.
2. When you encounter somebody before you during driving, you should send a signal at a distance of 5 m;.
3. The driving speed in the factory does not go beyond 5 km/h;.
4. When driving, the low point of the cargo need to be 0.3 m ~ 0.4 m above the ground;.
5. The transforming need to not be as well sharp to prevent the tendency of " complimentary turning";.
6. Adding and down the incline should be slow-moving and consistent, and no switching on the incline is permitted.
7. Do not drive across the slope. When the slope is more than 10%, the automobile ought to be driven backwards when going downhill;.
8. When the forklift employees carry the goods and move forward, if they experience large or heavy goods and go to the motorist's view, they need to take the turning around exercise
.
The "Eight Prohibitions" must be complied with in the operation.
1. Single fork procedure is not enabled.
2. It is not permitted to lift the goods for long distance driving.
3. It is not permitted to pick up the goods by passing on the pallet with the fork.
4. It is not enabled to straight shovel chemicals, flammables and various other dangerous chemicals with forks.
5. It is not allowed to utilize inertia pressure to get the Stand-on Electric Pallet Stacker goods.
6. It is not allowed to use braking pressure to exile round or easy-to-roll objects.
7. It is not permitted to bring people to deal with the pallet or fork, and it is Electric Forklift Truck for Warehouse purely forbidden to stand under the fork after the fork is raised.
8. Do not drive side to side on inclines
.
Vehicle parking is not allowed under the following problems.
1. Curves, narrow roads, train crossings;.
2. Areas with a longitudinal slope higher than 5%.
3. When there is an barrier on one side of the road, the contrary side of the section with the exact same length as the barrier ought to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844